Dec 3, 2020 Career by admin

Above values from ASTM A Higher strengths can be produced by heavy cold work – this may be required for certain applications. ASTM A – 16 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging. This specification covers. See the chemical composition and physical properties of ASTM A Grade annealed Stainless Steel, find alternative materials, and connect with suppliers.

Author: Faedal Shakticage
Country: Iraq
Language: English (Spanish)
Genre: Relationship
Published (Last): 14 February 2004
Pages: 374
PDF File Size: 3.57 Mb
ePub File Size: 19.66 Mb
ISBN: 618-7-98137-867-9
Downloads: 90602
Price: Free* [*Free Regsitration Required]
Uploader: Faem

The steel shall conform to the required chemical composition requirements. Resistance to Intergranular Corrosion 8. Historical Version s – view previous versions of standard.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

ASTM A for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

The following coatings may be specied: Such requirements may include, but are not limited to the following: Material can be manufactured to tensile strength ranges other than those shown in Table 2. The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. The material shall also conform to the requirements as to mechanical properties.


This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. Current edition approved Jan.

The following lubricants may be specied: All austenitic grades in the annealed condition or annealed and lightly drafted condition shall be capable of passing the criteria set by this specification. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Copyright ASTM Standard Specication for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging1 This standard is issued under the xed designation A ; the number immediately following the designation indicates the astj of original adoption or, in the case of revision, the year of last revision.

This standard has been approved for use by asfm of the Department of Defense.

ASTM A493 for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

B Product analysis tolerance over the maximum limit for carbon and nitrogen to be 0. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

The producer should be consulted when material is required to tensile strength ranges other than those specied. ASTM does not give any warranty express or implied or adtm any representation that the contents asm this abstract are accurate, complete or up to date.


For smaller sizes, similar mechanical properties apply to ferritic and martensitic grades; however the producer should be consulted regarding somewhat higher tensile properties applicable to austenitic grades. This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor. Soap is generally used. A number in parentheses indicates the year of last reapproval.

ICS Number Code The SI equivalents are in parentheses and may be approximate.

NOTE 1—A typical ordering description is as follows: Link to Active This link will always route to the current Active version of the standard. This abstract is a brief summary of the referenced standard. Last previous edition A — Packaging and Package Marking 9.

General Requirements for Delivery 4. An electroplated copper coating is often used. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Originally published as A aztm It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.